Most electrical problems get poked at before anyone calls. A tripped breaker gets reset. A dead outlet gets tested with a phone charger. A flickering light gets a new bulb. That is all reasonable, and most of the time it narrows down what is actually wrong. The point where it stops being sensible is when the breaker trips again, the outlet stays dead after the GFCI is reset, or the flickering follows the circuit rather than the fixture. That is when the wiring itself needs to be looked at, and that is what we do.
We handle residential and commercial electrical work in Kermit and across Winkler County. Homes here run the full range of wiring ages and panel types, and the jobs reflect that: repairs and troubleshooting, panel replacements, new circuits, outdoor wiring, and upgrades that bring older properties in line with what they are actually being asked to carry. Call us, describe what you are seeing, and we scope the job on the phone before anything is scheduled. That is how it starts every time, whether the work turns out to be a single outlet or a full rewire.
We cover this area, and the number is (432) 326-6289.
Electrical quotes are not flat rates because the work does not have a flat shape. What looks like a straightforward outlet replacement can turn out to involve a backstabbed connection that failed upstream, a circuit that has been daisy-chained past what the breaker can safely carry, or a box wired without a ground. What the fault turns out to be, what has to be opened up to reach it, and whether the existing panel can carry a change without a capacity issue are the things that move a price.
We go through all of that on the call. You describe the symptom, we ask the questions that help us scope it, and we give you a price before anything is put on the calendar. No-pressure estimates, priced up front, so you know what you are agreeing to before we show up. If the scope changes when we get there because the situation is different from what the call indicated, we tell you before doing anything additional. You are not committed to work that was not discussed.
The jobs we take in this town reflect the housing stock and the way properties here are actually used. Older homes on original wiring, outbuildings that were wired in stages, well equipment, and the additions that get put on a house over the years all generate specific kinds of electrical work. Here is what that looks like in practice.
A Level 2 home charger needs a dedicated 240-volt circuit, and the first question is always whether the panel has the capacity to carry it. Driving distances in and around Kermit make home charging practical rather than optional for EV owners. We run the load calculation, determine what the panel can support, run the dedicated circuit to where the charger mounts, and handle any panel work the calculation identifies before we start the circuit run.
Outdoor outlets on a property in this region take sun and heat that wear through standard covers and boxes faster than they would elsewhere. We install weatherproof outlets and in-use covers for patios, workshops, and outbuildings, and we make sure the circuit feeding them has the GFCI protection required for exterior locations. Misting system circuits and RV hookups come up regularly on properties here, and those are part of what we wire.
Smart switches and dimmers are not always a straight swap. A box that is missing a neutral wire, or a circuit that was run without a ground, needs to be addressed before a smart device will work correctly. We assess the box first, handle the wiring condition, and then install the device so it operates the way it is supposed to. Forcing a smart switch into a box that is not set up for it is how you end up with a device that works intermittently or not at all.
Properties outside of town often have well pumps, irrigation controls, or outbuilding equipment running on circuits that were added without much documentation. A well pump circuit that trips repeatedly under normal load, or an irrigation panel that has been spliced and extended past its original design, needs to be traced and assessed rather than just reset. We handle dedicated circuit installation for well equipment and irrigation systems, and we address the grounding and bonding that those circuits require.
Panels in older Kermit homes were sized for loads that did not include modern appliances, air conditioning running continuously through a West Texas summer, or any of the added circuits that accumulate on a property over time. A panel that is running hot, showing signs of heat damage at the connections, or simply too small for what it is carrying needs to be replaced rather than patched. We handle full panel replacements, subpanel installation for outbuildings and workshops, and breaker replacement where the panel itself is sound but individual breakers have failed.
Wiring is easier to deal with when somebody explains it plainly, and the first step is knowing what is actually there. Older homes in this part of Winkler County turn up a range of wiring conditions, and not all of them are emergencies. Some are fine left alone. Some need to be addressed before a property can safely carry additional load.
Aluminum branch-circuit wiring is one of the more common conditions we find in homes of a certain age. It is not automatically dangerous, but it requires specific connectors and devices rated for aluminum conductors at every outlet, switch, and fixture. Where those connections have not been maintained or were never made correctly, the risk of heat buildup at the connection point is real. Aluminum-wiring remediation covers those connection points throughout the home, and in some cases it means replacing the branch circuits rather than working with what is there.
Knob-and-tube wiring, where it turns up, gets assessed for condition and for how it has been modified over the years. Original knob-and-tube in good condition and left alone is a different situation from knob-and-tube that has been spliced into, buried under insulation, or asked to carry loads it was never designed for. We explain what we find and walk through the practical options before any work is recommended. Whole-home rewiring comes up when the wiring condition or the scope of what needs to change makes partial remediation the longer path.
Arc-fault and ground-fault breaker requirements also come into the picture when older wiring is being updated. AFCI protection is required in bedrooms and living areas under current code, and GFCI protection is required in kitchens, bathrooms, garages, and outdoor locations. We address both as part of any panel or wiring work, and we handle them as standalone upgrades when a property needs to be brought current.
Not every power problem in a home is a wiring problem. Some of them belong to the utility side of the meter, and knowing which is which matters before any work is done.
The dividing line runs at the meter. Everything from the meter into the home, including the panel, the branch circuits, the outlets, and the fixtures, is on our side. The service entrance conductors from the utility connection to the meter base, and the transformer and lines feeding the property, belong to the utility. A problem that shows up as low voltage, intermittent power on one leg of the service, or a complete outage that does not correspond to anything on the panel is often a utility issue rather than a wiring fault.
When we go through a problem on the call and the description points toward the utility side, we say so. If a visit is needed to confirm it, we confirm it and then walk you through what to report to the utility and what to expect from their process. We do not bill for work on equipment that is not ours to repair. What we do is make sure the fault is correctly identified so the right call gets made.
Appointments are set on the call. You describe what you need, we scope it, confirm the price, and find a time that works. We are available every day from 8:00 AM to 8:00 PM, seven days a week. If the problem is urgent, ask about short-notice availability when you call. Call and ask what is open.
For tenants and rental properties, we coordinate with whoever needs to be present and confirm access before we show up. For businesses that have to stay open, we work through what can be done without interrupting the operation and what requires a scheduled outage window. That conversation happens on the call, before anything is booked.
You know who to call if you ever need us again.
The number is (432) 326-6289, and the process is the same every time: call, get the scope, get the price, get it on the calendar.
Plain answers. Clear options. Safe wiring.
We cover Kermit as our primary market in this area, and we take calls from across Winkler County. Nearby communities including Wink and Monahans are part of the area we serve. Whether the property is in town or out on a rural parcel, the process is the same: call, describe what you need, and we confirm whether we can get to you and when. There is a fuller write-up on the list of electrical services we handle.
We plan the work around the business's schedule wherever possible, which may mean phasing the job, isolating circuits that are not in active use, or scheduling disruptive work before or after business hours. Call and describe the operation and we will work out an approach that keeps the disruption manageable.
The rough-in stage, when wiring is run before walls are closed, and the finish stage, when devices and fixtures are installed, both require an electrician on site. If the project involves a panel change or a service upgrade, that work needs to happen before other trades that depend on the electrical supply. We coordinate with the build schedule when you call.
If a neighbor on the same utility transformer loses power simultaneously, the cause is almost certainly on the utility side rather than inside your home. We still want to hear about what you are experiencing, because a utility event can sometimes mask a separate issue inside the panel that becomes apparent when power is restored.
We need clear access to the panel to work safely, and if it is blocked we will need it cleared before the job can proceed. If you know access is an issue, mention it on the call so we can plan around it and avoid a wasted trip.
If the utility has confirmed that power is reaching the meter and a breaker inside the panel still will not hold, the fault is on the home side. That can mean a failing breaker, a fault in the branch circuit it feeds, or a load on that circuit that exceeds what the breaker is rated for.
Call (432) 326-6289 and describe which circuit is involved and what is running on it.
We can often narrow down the cause on the call and schedule a visit to trace and correct it.
A well pump draws a significant starting load and needs a dedicated circuit sized for that draw, not a shared circuit that is also running other equipment. Grounding and bonding requirements for well equipment are specific, and we address those as part of the circuit installation. If the existing circuit has been extended or modified over the years, we trace it before recommending whether to repair or replace it.
A breaker that trips only at specific times usually points to load, not a wiring fault. If the circuit is shared with equipment that runs on a schedule, or if heat builds up in the panel or wiring during the hottest part of the day, the breaker can reach its trip threshold only under those conditions. We ask about the timing and what is running when it happens to narrow down the cause.
We handle repairs, panel replacements, wiring, outlets, lighting, EV charger circuits, outdoor wiring, generator hookups, and electrical safety inspections for homes and businesses in Kermit, Wink, Monahans, and across Winkler County.
Call (432) 326-6289 for a quote.
We are available every day from 8:00 AM to 8:00 PM. Tell us what you are dealing with and we will tell you what it takes to fix it. If you are in the surrounding area, that call reaches us too.
Other towns where we take electrical work: West Odessa, Andrews, Crane.
Have a look at our service area list.
We handle the full range of electrical work for homes and businesses across Kermit and Winkler County, from a single tripped breaker to a complete service upgrade. The table below covers what each service involves, who it fits, and what is worth knowing before you call. Scope is confirmed on the phone, and the price is settled before anything is scheduled.
Call (432) 326-6289 and tell us what you are dealing with.
| Electrical Service | What the Job Involves | Best For | Worth Knowing |
|---|---|---|---|
| Wiring & Rewiring |
| Older homes with outdated or unsafe wiring systems | Aluminum and knob-and-tube wiring are common in older Kermit homes. We assess what is present and explain the options before any work starts. |
| Electrical Panel & Service Upgrades |
| Homes adding EV chargers, solar systems, or high-draw equipment, and older homes with undersized panels | Kermit summers put continuous heavy load on panels. We run a load calculation to find out exactly what your service can carry before recommending any upgrade. |
| Electrical Safety Inspections |
| Buyers, sellers, landlords, and property managers wanting a clear picture of the electrical system | These inspections are useful before a purchase, before a tenant moves in, or any time you want to know where things stand. |
Call (432) 326-6289 to talk through what you are dealing with and get a straight answer on what it will take to fix it.
(432) 326-6289